Installation
Instructions
MOUNTING
**As
this will become your most used kitchen appliance, Point
and Cut recommends mounting the unit above the sink
area, or close to your sink or food prep area. This is
the preferred location suggested by existing Point and
Cut owners.**
The Point and Cut
requires a flat mounting surface. It may be
necessary to install spacers if the front edge of your
cabinets hangs lower than the bottom of the
cabinets. These spacers will be located between
the mounting holes on the Point and Cut and the bottom
of your cabinet.
IMPORTANT:
There needs to be a MINIMUM of 13” of space between the
surface that the Point and Cut is mounted to and your
countertop.
Have an assistant hold
the Point and Cut up to the location it is to be mounted
under your cabinets. Using a pencil, mark the
location of each of the (10) mounting holes.
Mount using the #6 X 1/2" L screws provided.
It helps to drill small
"starter" holes for the (10) mounting screws.
Then, run a screw in and out of each of the holes before
actually mounting the unit.
NOTE: To
assure proper operation it is necessary that the gaps
between the MAIN BODY and the outer RIGHT and LEFT side
panels are evenly spaced. You may find it
necessary to slightly loosen the screws after mounting and adjust
the RIGHT and LEFT side panels to make the gaps on the
right and left sides even. (The spaces between the
main body and the RIGHT and LEFT side panels need to be
the same distance on each side.) See gap areas
depicted by the WHITE arrows in Picture #1.
Picture #1
ELECTRICAL CONNECTION:
Plug the AC adapter into
an electrical outlet.
WARNING:
Do NOT plug the Point and Cut into an electrical outlet
until it has been installed.
Do NOT operate the Point and Cut with it sitting on a
flat surface.
If your electrical outlet
is inside your cabinets, it will be necessary to remove
the DC plug from the Point and Cut, run the plug down
through a hole in the bottom of your cabinet, and then
re-install it to the Point and Cut.
IMPORTANT: If you
plugged the Point and Cut into an electrical outlet,
UNPLUG it from the electrical outlet BEFORE PROCEEDING.
Failure to do so will permanently damage the power
supply.
To remove the DC plug from the Point and Cut,
open the unit to the full open position.
(See step
#1 in LOADING instructions.)
The DC plug is located in the rear and on the inside
upper portion of the RIGHT side panel. See YELLOW
arrow in Picture #2.
Picture #2
Remove the (2) screws and the small metal plug cover.
Slide the wire end (rear end) of the DC plug out of its
slot and the nose end (front end) will come out of the
locater hole. Cut the tie-wrap that is attached to
the upper rear cross bar.
With the DC plug now unattached, it can be run down
through a hole in the bottom of your cabinets.
To re-attach the DC plug slide the nose end of the plug
through the locater hole it was removed from, and then
slide the wire end back into its slot. Next, the
small metal plug cover must be re-installed.
Lastly, the power cord needs to be re-attached to the
upper rear cross bar. Use the tie-wrap supplied in
the bag of installation screws.
NOTE: If your power supply fails it must be
replaced with an Ault Inc. power supply Part# P48240500A200G.
DIMENSIONS:
12" D x 6.5" H x 17.5" W
(Dispenser width
WITHOUT mounting flanges is 17.5")
(Dispenser width WITH mounting flanges is 20")
Loading Instructions
To load a new roll of
paper towels:
1. Place hands as shown in
Picture #3. Pull toward you and then downward to
open cabinet. (Make sure to open to full open
down position.) If not fully open, you will
not be able to load the paper towel.
Picture #3
2. Insert the dowel rod
through the center of the paper towel roll.
3. Place the dowel into
the cradle.
It is recommended that you place the roll into the
cradle so that the towel comes up from the bottom
front of the roll as shown at the WHITE arrow in
Picture #4.
Picture #4
4. Tear off the first
sheet of the paper towel roll to assure a fresh edge
when loading.
5. Insert the end sheet of
paper towel into the slot, as shown at the
RED arrow in picture
#4.
Operating Instructions
To unroll the length of
paper towel you desire, place your hand between the
sensors on the right side of the unit as shown above.
To cut the towel, place
your hand between the sensors on the left side of the
unit as shown above.
The
paper towel will remain hanging until the user takes it
away.
Helpful
Hints
-
To clean the stainless
steel, the drawer needs to be pulled down. This
disconnects the power which allows cleaning around the
sensor areas without activating "unroll" or "cut".
-
Customers have reported
that Endust does a nice job of cleaning the
stainless steel.
-
If the paper towel does
not feed out, tear off one (1) sheet and try reloading
with a fresh edge.
-
If the cutting
mechanism has not been activated, the drawer can be
opened and the paper towel can be rolled back up if
the user decides they dispensed more towel than
necessary.
-
Any size or brand of
household-style paper towel, like you get from the
supermarket, can be used.
Warranty
3 Year Limited Warranty
Your Point and Cut
Warranty covers defects in materials or workmanship of
this "No-Touch" Paper Towel Dispenser and at Point and
Cut's option will repair or replace this product or any
component of the product found to be defective at Point
and Cut's expense (less shipping and handling charges),
for 1 year from the date of original purchase.
After the first year and continuing through the third
year from the date of original purchase Point and Cut
will replace any parts that prove to be defective under
normal conditions without charge, excluding any labor
and Shipping and Handling charges incurred in the
performance of this warranty.
This
Warranty is valid for the original purchaser from the
date of the initial purchase and is not transferable.
It is recommended that you keep the original sales
receipt and the original packaging materials.
Proof of purchase and a Return Authorization number are
required to obtain warranty performance. (See
below for instructions to acquire a Return Authorization
number).
Specifically excluded from this warranty are failures
caused by connection to electrical service other than
standard household current of 120VAC, accident, misuse,
neglect, abuse, including tampering, modifications or
attachments, unsuitable physical or operating
environment, maintenance by anyone other than Point and
Cut,
operation of the product beyond the limit of its duty
cycle, spills of food or liquid, external forces such as
floods, fires, acts of God or other circumstances beyond
Point and Cut's control.
This warranty gives you specific legal rights and you
may also have other rights, which vary from state to
state.
The warranties described shall be in lieu of any other
warranties expressed or implied, and all warranties of
every nature shall be limited to the periods of time
therein stated.
Point and Cut will not be liable for any damages of any
kind resulting from the purchase, use or misuse of, the
product. Point and Cut assumes no liability
greater than the original purchase price.
For assistance with
installation or operating the Point and Cut
paper towel dispenser, or for instructions
on repairs or replacement, please
E-mail
info@cleancutdispenser.com
with your Contact information, type of problem
you are having and a good time to reach you and a
service technician will contact you. If a service
technician deems a repair is necessary, Point and Cut
will assign a Return Authorization number to you.
